Products / Wicher 500i Ex

Wicher 500i Ex turbo card has been designed for installation inside Amiga A500/A500+ computer. It supports 68000/68010 CPUs (using PLCC68 package), up to 8 MB of Fast RAM (using standard SIMM72 memory modules) and IDE 2,5” hard drives. CPU clock speed can be set up to 50 MHz.

Wicher 500i Ex came into being as a universal solution for users looking for highly-clocked MC68000/MC68010 classic Amiga CPUs. (Stable configurations running at 50 MHz have been confirmed when paired with MC68HC000 series chip. Unfortunately, not every unit is capable of performing at this clock speeds over longer periods of time.)
Our product allows expanding Amiga’s RAM with standard 1/2/4/8MB 50/60 ns SIMM72 FPM/EDO memory modules. It also provides a necessary interfaces for connecting 2,5” IDE hard drive and SPI bus-equipped modules (e.g. RTC, Ethernet).

 

Features

  • AmigaA500/A500+ compatibility (in place of the original CPU),
  • PLCC68-packaged MC68000, MC68HC000, MC68010 chip support,
  • recommended chip version: MC68HC000 (not included),
  • recommended Kickstart version: Kickstart 3.1,
  • supported CPU clock speeds: 12,14,16,25,28,42,48,50 MHz,
  • RAM expansion: industry standard SIMM72 (FPM/EDO) 1-8MB, 50/60ns memory modules (not included),
  • Amiga A600-compatible IDE controller,
  • SPI controller
  • RTC clock, NVRAM memory,

 
 

Benchmarks

  • Amiga 500 (Custom Kickstart 3.1, MC68HC000FN16 CPU running @50MHz, scsi.device V46.0)
  • MIPS: ~4.43
  • Dhrystones: ~4245
  • IDE transfer speeds: ~3.1MB/s (using IdeFix97 ~5.8MB/s)
  • RAM transfer speeds: ~6.99MB/s

The above results have been achieved with SysInfo 4.0, AIBB 6.5

 


 

Software

The provided software facilitates user-inititated configuration changes via CLI command or additional WicherBootMenu module, allowing creation of custom Kickstart versions (with Remus program). WicherBootMenu can be accessed by holding down the left mouse button when turning on or rebooting your Amiga.

 

 

 


Wicher list of options
VERSION - display version information
STATUS - display actual Wicher config
LOAD - load config from a file
SAVE - save config to a file
CLK - change CPU clock speed
FASTMEM - (on/off) enables/disables FAST RAM
CFGRAM - automatic configuration of memory controller
IDE - (on/off) enables/disables IDE controller
SPI - (on/off) enables/disables SPI controller
RAS13 - (on/off) enables/disables support for additional memory banks in the SIMM module (two-sided modules).
BIGRAM - (on/off) enables/disables support for SIMM module 16MB-128MB (experimental function)

Example: wicher clk=28 RAS13=on

 


Please note!!!

Not every CPU unit remains stable when overclocked (i.e. clocked with higher speeds than the one prescribed by its manufacturer).

Most SIMM72 memory modules should function correctly at 12-28 MHz clock speeds. However, not every unit will operate without errors at 35-50 MHz clock speeds.

 
 
 



Quick Guide:

 

User manual:

 

Software: WicherInstaller v2.2,   WicherInstaller.adf,  ChangeLog

 


SPI - Pin Configuration


Signal Pin Description
+5V 1 Supply Voltage
INT 2 Interrupt
SS2 3 Slave Select 2
SS3 4 Slave Select 3
SS0 5 Slave Select 0
SS1 6 Slave Select 1
MOSI 7 Master Out Slave In
SCLK 8 Clock
GND 9 Ground
MISO 10 Master In Slave Out

JTAG


 

 





Schematics

 



MP3 CODEC


 

VS1003

 

Wicher SPI busVS1003/1053 MP3 CODEC
+5V5V
INTDREQ
SS2XDCS
SS3XRST
SS0
SS1XCS
MOSIMOSI
SCLKSCK
GNDDGND
MISOMISO

 



SD Card


 

SD Card

 

WARNING!!! Remove resistors R1, R2, R3, R4

Wicher SPI busSD Card - MOD-01507
+5V5V
INT
SS2CS
SS3
SS0
SS1
MOSIMOSI
SCLKSCK
GNDGND
MISOMISO

 


microSD Card

 

Wicher SPI busmicroSD Card - Pololu #2597 (PLL-02696)
+5Vuse 3.3V regulator for the VDD pin
INT
SS2CS
SS3
SS0
SS1
MOSIDI
SCLKSCLK
GNDGND
MISODO

 



Ethernet


 

ENC28J60 Mini

 

Wicher SPI busENC28J60 Mini
+3.3VVCC
INTINT
SS2
SS3
SS0
SS1CS
MOSISI
SCLKSCK
GNDGND
MISOSO